Sun Microsystems, Inc.  Sun System Handbook - ISO 3.4 June 2011 Internal/Partner Edition
   Home | Current Systems | Former STK Products | EOL Systems | Components | General Info | Search | Feedback

Asset ID: 1-73-1000376.1
Update Date:2010-08-23
Keywords:

Solution Type  FAB (standard) Sure

Solution  1000376.1 :   StorEdge 6130 FC Controller replacement procedures do not mention that you might have to reset the IP address, Gateway and or Netmask.  


Related Items
  • Sun Storage 6130 Array
  •  
Related Categories
  • GCS>Sun Microsystems>Sun FAB>Standard>Reactive
  •  

PreviouslyPublishedAs
200498


Product
Sun StorageTek 6130 Array

Bug Id
<SUNBUG: 6349345>

Part
  • Part No: 375-3216
  • Part Description: StorEdge 6130 FC Controller

Impact

In order to properly administer a StorEdge 6130 array, the Management Host requires out of band network access to both controllers. At the time of installation, the customer can select to accomplish this task by using either Static or Dynamic IP address assignment. For those customers that use the Static method and use a non-default address (default=192.168.128.101/102), there is nothing in the FC Controller replacement procedure indicating that you must reset the IP address, Gateway or Netmask of the new controller.

It is likely that, in most of these instances, the array has already been in production for some time and thus the impact of this may not be immediately obvious.


Symptoms

After replacing a controller, attempts to create or modify volumes may result in the following error messages if the IP address, Gateway or Netmask is not updated:

"This operation must be performed by the alternate controller. This modification attempt failed."

or

"This operation must be performed by the alternate controller. This creation attempt failed."

Examples of activities that may prompt these errors are:

  • Manually moving a volume from one controller to another
  • Creating snapshots

Also attempts to upgrade firmware on the array may hang. Waiting up to 2 hours may display timeout errors like:

"Connection timed out"

or

"One of the controllers is not reachable."


Root Cause

The need for having to manually update the IP address, Gateway and Netmask was not foreseen.


Workaround

After the replacement of a failed controller (A in the example below), the IP address, Gateway and Netmask of the controllers should be verified by any of the following commands:

Using a current 6130SupportData output:

# egrep 'Tray.0.Controller|IP address' storage* | head -8
        Tray.0.Controller.1
             IP address: 192.168.128.101
             Subnet mask: 0.0.0.0
             Gateway: 0.0.0.0
        Tray.0.Controller.2
             IP address: 192.168.128.12
             Subnet mask: 255.255.255.128
             Gateway: 192.168.128.1

Notice that the A controller (Tray.0.Controller.1) has a default IP address, Gateway and Netmask but the B controller doesn't.

Using the GUI:

Access the GUI using the IP address of the Management Host:

     https://<ip_address>:6789

  • Login using any valid "storage" or "guest" user role
  • Select StorEdge 6130 Configuration Service
  • Select the Array from the Array Summary page
  • Select Controllers from the Physical Storage tab
  • Note the IP address, Gateway and Netmask of the two controllers.

Earlier versions of the Management Host Software have the Controllers under the Administration tab.

Using the CLI after logging in as a valid user:

# sscs list -a <array_name> controller | egrep 'IP|Controller|Gateway|Mask'
Controller: A
  IP Address: 192.168.128.101
  Gateway: 0.0.0.0
  Net Mask: 0.0.0.0

Controller: B
  IP Address: 192.168.128.12
  Gateway: 192.168.128.1
  Net Mask: 255.255.255.128

Again, the A controller has a default IP address, Gateway and Netmask but the B controller doesn't.

----------------------------

Comprehensive Field Instructions:

Before replacing any controller, the Service Engineer should, using the methods described above, record what the current IP address, Gateway and Netmask of that controller is. After a controller is replaced, the IP address, Gateway and Netmask of the replacement controller should then be verified to have been appropriately updated. In the cases of customers using either DHCP/BOOTP or default settings, the update should be automatic. If the IP address, Gateway or Netmask do require a manual update, either of the following methods can be used.

A) GUI:

Access the GUI using the IP address of the Management Host:

    https://<ip_address>:6789

  • Login using either root or other valid "storage" user role
  • Select StorEdge 6130 Configuration Service
  • Select the Array from the Array Summary page
  • Select Controllers from the Physical Storage tab*
  • Scroll down to the appropriate controller (1=A, 2=B)
  • Select the "Specify Network Connection" button
  • Enter the appropriate IP address, Gateway & Netmask
  • Select OK to save the changes
  • Logout upon confirmation of successful changes.

Earlier versions of the Management Host Software have the Controllers under the Administration tab.

B) CLI after logging in as a valid "storage" user role:

# sscs modify -a <array_name> -g <gateway_ip_address> -i <ip_address> \ -m <netMask> controller [A|B]


Resolution

A bug report (6349345) has been filed and should be addressed in a future release of the product.


Previously Published As
102077
Internal Comments


None


Related Information
  • Other: StorEdge 6130 Service Advisor

Internal Contributor/submitter
[email protected]

Internal Eng Business Unit Group
KE Authors

Internal Eng Responsible Engineer
[email protected]

Internal Services Knowledge Engineer
[email protected]

Internal Kasp FAB Legacy ID
102077

Internal Sun Alert & FAB Admin Info
Critical Category:
Significant Change Date:
Avoidance: Workaround
Responsible Manager: null
Original Admin Info: null

Internal SA-FAB Eng Submission
StorEdge 6130 FC Controller replacement procedures do not mention that you might have to reset the IP address, Gateway and or Netmask.

Product_uuid
8252cb91-d771-11d8-ab52-080020a9ed93|Sun StorageTek 6130 Array

Attachments
This solution has no attachment
  Copyright © 2011 Sun Microsystems, Inc.  All rights reserved.
 Feedback