Sun Ultra 45 Workstation
 
Sun Ultra 25 Workstation
 

PLA-Support>Sun Systems>Sun_Other>Sun Collections>SN-OTH: SPARC-CAP VCAP
 

In this Document

Goal

Fix

Replacing the I/O Module With the DVD-Dual Drive and Audio USB Board

Removing the DVD-Dual Drive

Installing DVD-Dual Drive

Applies to:

Goal

Sun Ultra 25/Ultra 45 Workstation - How to Remove and Replace a Sun Ultra 25 Workstation Front I/O Board and/or DVD Drive

Fix

 DISPATCH INSTRUCTIONS
   WHAT SKILLS DOES THE FIELD ENGINEER/ADMINISTRATOR NEED?:

Sun Ultra 25/Ultra 45 Workstation  product training is desirable but not required

   TIME ESTIMATE: 40 mins

   TASK COMPLEXITY: 0

FIELD ENGINEER/ADMINISTRATOR INSTRUCTIONS:
   PROBLEM OVERVIEW: DVD

   WHAT STATE SHOULD THE SYSTEM BE IN TO BE READY TO PERFORM THE RESOLUTION ACTIVITY?:

A data backup is not a pre-requisite but is a wise precaution.
The customer should conduct an orderly software system shutdown.

   WHAT ACTION DOES THE FIELD ENGINEER/ADMINISTRATOR NEED TO TAKE?:

Replacing the I/O Module With the DVD-Dual Drive and Audio USB Board

This section describes removal and installation of the I/O module. The I/O module contains the DVD-dual drive, the audio USB board with speaker, USB and audio connectors, and the Power button and LED.

Removing the DVD-Dual Drive

If you are only replacing the DVD-dual drive:

 - a. Using a No. 0 Phillips screwdriver, remove the screws holding the DVD-dual drive into the I/O module.

 - b. Pull the DVD-dual drive straight out the back of the removable media bay

6. If you are replacing the audio USB board:

 - a. Remove the DVD-dual drive and set it aside.

 - b. Using a No. 2 Phillips screwdriver, remove the four screws that secure the audio USB board to the I/O module.

 - c. Pull the audio USB board straight out the back of the removable media bay

Installing DVD-Dual Drive

1. Remove the DVD-dual drive assembly from the packaging.

2. If you are replacing the audio USB board:

 - a. Install the new audio USB board into the removable media bay.

 - b. Replace all four screws that secure the audio USB board to the removable media bay.

3. Install the DVD-dual drive into the I/O module with the screws:

 - a. If you are using the old DVD-dual drive, screw the old drive into the I/O module.

 - b. If you are using a new DVD-dual drive, screw the new drive into the I/O module.

4. Push the I/O module and DVD-dual drive into the chassis until the module clicks

5. Connect the cables to the DVD-dual drive and the audio USB board.

Note - Always use the new cables that are shipped with the DVD-dual drive

6. Guide the DVD and audio/power cables through the I/O cable clip at the top of the chassis and close the clip.

7. Reconnect the audio and USB cables to:

 - Audio and power cable at J3 on the motherboard and J0201 on the audio USB board

 - DVD cable at J11 on the motherboard and J501 on the DVD-dual drive

 - USB cable at J36 on the motherboard and J0601 on the audio USB board

8. Inspect the audio USB board cabling to verify that:

 - The I/O cable clip is closed and locked.

 - The USB cable is secured in the cable clip on the hard drive bay.

9. Reassemble the workstation. Power on the system, and verify the audio USB board installation.

OBTAIN CUSTOMER ACCEPTANCE
   WHAT ACTION DOES THE FIELD ENGINEER/ADMINISTRATOR NEED TO TAKE TO RETURN THE SYSTEM TO AN OPERATIONAL STATE?:

Restart software applications per applicable administration guides to resume system operation.

PARTS NOTE:

https://support.oracle.com/handbook_private/Systems/Ultra25/components.html

https://support.oracle.com/handbook_private/Systems/Ultra45/components.html

REFERENCE INFORMATION:

Please refer to the Sun Ultra 25/Ultra 45 Workstation Service and Diagnostics Manual: http://docs.oracle.com/cd/E19127-01/ultra25.ws/819-1892-12/819-1892-12.pdf

This solution has no attachment