Sun Microsystems, Inc.  Sun System Handbook - ISO 4.1 October 2012 Internal/Partner Edition
   Home | Current Systems | Former STK Products | EOL Systems | Components | General Info | Search | Feedback

Asset ID: 1-71-1349656.1
Update Date:2011-11-04
Keywords:

Solution Type  Technical Instruction Sure

Solution  1349656.1 :   How to Remove and Replace a Ultra 24 Workstation DVD Drive:ATR:1349656.1:0  


Related Items
  • Sun Ultra 24 Workstation
  •  
Related Categories
  • PLA-Support>Sun Systems>Sun_Other>Sun Collections>SN-OTH: x64-CAP VCAP
  •  




In this Document
  Goal
  Solution


Applies to:

Sun Ultra 24 Workstation - Version: Not Applicable to Not Applicable - Release: N/A to N/A
Information in this document applies to any platform.

Goal

How to Remove and Replace a Ultra 24 Workstation DVD Drive

Solution

DISPATCH INSTRUCTIONS
- WHAT SKILLS DOES THE ENGINEER NEED: Nothing beyond basic hardware and Solaris training
- TIME ESTIMATE: 60 minutes
- TASK COMPLEXITY: 0

FIELD ENGINEER INSTRUCTIONS:
- PROBLEM OVERVIEW:How to Remove and Replace a Ultra 24 Workstation DVD Drive
- WHAT STATE SHOULD THE SYSTEM BE IN TO BE READY TO PERFORM THE
RESOLUTION ACTIVITY?:
- WHAT ACTION DOES THE ENGINEER NEED TO TAKE:

1. Powering Off the System and Removing the Left-Side Access Panel.

I. Power off the system and all the peripherals connected to it.
II. Turn the power switch on the back of the chassis to the Off position.
caution icon Caution - Failure to properly turn off the system before you start installing components can cause serious component damage.
III. To maintain system grounding, do not unplug the AC power cord from the back of the system unless the specific procedure instructs you to unplug it.
IV. Loosen the two captive thumbscrews located on the rear edge of the left side access panel
V. Slide the access panel approximately 1.5 cm toward the back of the workstation.
VI. Tilt the top edge of the panel out, then lift the panel upward.
VII. Carefully set the panel aside.

Replacing the DVD Drive

This section describes the procedures to remove and install the DVD drive.
procedure icon To Remove the DVD Drive
1. Remove any media in the DVD drive
2. Follow the instructions in Powering Off the System and Removing the Left-Side Access Panel.
3. Remove the front bezel
4. Disconnect the cables from the back of the DVD drive
5. Push the drive retaining lever tab up to release the retaining hooks
6. Gently pull out the DVD drive from the front of the chassis.
7. Place the DVD drive on an antistatic surface.

Install the DVD Drive

2. Remove the new DVD drive from its packaging.
3. Lifting the front end slightly, slide the 5.25-inch DVD drive into the drive bay until the holes on the side align with the hooks on the drive retaining lever.
4. To lock the drive in the drive bay, rotate the drive retaining lever downward.
5. Verify that the drive is captured by the retaining hooks.
6. Connect the SATA, power, and jumper cables to the back of the DVD drive.
Refer to the cabling diagram in the service label on the side of the chassis for information about correct cable routing.
7. Replace the front bezel and left side cover of the workstation.
8. To close the system, perform the steps in To Prepare for Service.

OBTAIN CUSTOMER ACCEPTANCE
- WHAT ACTION DOES THE CUSTOMER NEED TO TAKE TO RETURN THE SYSTEM TO
AN OPERATIONAL STATE:

PARTS NOTE:

REFERENCE INFORMATION:

Sun Ultra 24 Workstation Service Manual
http://download.oracle.com/docs/cd/E19127-01/ultra24.ws/820-2480-12/


Attachments
This solution has no attachment
  Copyright © 2012 Sun Microsystems, Inc.  All rights reserved.
 Feedback