Sun Microsystems, Inc.  Sun System Handbook - ISO 4.1 October 2012 Internal/Partner Edition
   Home | Current Systems | Former STK Products | EOL Systems | Components | General Info | Search | Feedback

Asset ID: 1-71-1310014.1
Update Date:2012-08-01
Keywords:

Solution Type  Technical Instruction Sure

Solution  1310014.1 :   How to Replace a T5120/T5220 Graphics Card:ATR:1387:0  


Related Items
  • Sun SPARC Enterprise T5120 Server
  •  
  • Sun SPARC Enterprise T5220 Server
  •  
Related Categories
  • PLA-Support>Sun Systems>Sun_Other>Sun Collections>SN-OTH: SPARC-CAP VCAP
  •  
  • .Old GCS Categories>Support>KM>Content>Video
  •  




In this Document
Goal
Fix


Applies to:

Sun SPARC Enterprise T5220 Server - Version Not Applicable and later
Sun SPARC Enterprise T5120 Server - Version Not Applicable and later
Information in this document applies to any platform.

Goal

How to remove and replace a T5120/T5220 Graphics Card

*********************************************************************
To report errors or request improvements on this procedure,
please Add a Comment on Doc ID: 1310014.1
*********************************************************************


Video - ATR1387 (3:15)

Fix

DISPATCH INSTRUCTIONS

WHAT SKILLS DOES THE ENGINEER NEED:(IS A SITE ENGINEER AVAILABLE?)
T5120/T5220 knowledge or training recommended but not required

TIME ESTIMATE: 60 minutes

Task Complexity: 0

FIELD ENGINEER INSTRUCTIONS

PROBLEM OVERVIEW:  Faulty Graphics Card

WHAT STATE SHOULD THE SYSTEM BE IN TO BE READY TO PERFORM THE RESOLUTION ACTIVITY? :

A data backup is not a pre-requisite but is a wise precaution.

Customer should shut the operating system down gracefully (using "init 0"), and after the system has shut down Switch from the system console to the -> prompt by typing the #. (Hash Period) key sequence. At the -> prompt, type the stop /SYS command.

WHAT ACTION DOES THE ENGINEER NEED TO TAKE:
*** Follow standard ESD procedures to avoid Electrostatic Discharge

1. Disconnect all power cables
2. Remove the Top Cover
-Unlatch the fan module door by pulling the release tabs back to release the door
-Press the top cover release button and slide the top cover to the rear about a 0.5
inch
-Lift up and remove the cover

Removal:

1. Locate the Graphics card that you want to remove. Note its corresponding riser board.
2. If the graphics card is in a 2u T5220 Riser Board, note the connector of that Riser Board to which the Graphics Card is installed.
3. Unplug all cables from the card.
Note the location of all cables for reinstallation later.
4. Remove the riser board.
5. Carefully remove the Graphics card from the riser board connector.
6. Place the Graphics card on an antistatic mat.

Installation:
1. Unpack the replacement Graphics card and place it on an antistatic mat.
2. Locate the proper Graphics slot for the card you are replacing.
3. Remove the Graphics riser board.
4. Insert the Graphics card into the correct slot on the riser board.
5. Replace the Graphics riser.
6. Install the top cover.
7. Slide the server into the rack.
8. Connect any data cables required to the Graphics card.
Route data cables through the cable management arm.
9. Connect the power supplies.
Note: As soon as the power cords are connected, standby power is applied.
Depending on how the firmware is configured, the system might boot at this time.

OBTAIN CUSTOMER ACCEPTANCE

WHAT ACTION DOES THE FE/CUSTOMER NEED TO TAKE TO RETURN THE SYSTEM TO AN OPERATIONAL STATE:
Power on, boot system and monitor boot sequence for errors. Test functionality of system:
1. Run the Solaris "fmadm faulty" and SP/ILOM "show faulty" command (if only ALOM is supported run "showfaults -v" command) to verify that the fault has been cleared.
2. Perform one of the following tasks based on your verification results:
   * If the previous steps did not clear the fault, refer to doc 1004229.1 for information about the tools and methods you can use to diagnose and clear component faults.
   * If the previous steps indicate that no faults have been detected, then the component has been replaced successfully. No further action is required
3. Restart software applications per applicable administration guides to resume system operation.

PARTS NOTE:
None

REFERENCE INFORMATION:
Sun SPARC Enterprise® T5120 Server Service Manual
http://download.oracle.com/docs/cd/E19839-01/

Sun SPARC Enterprise® T5220 Server Service Manual
http://download.oracle.com/docs/cd/E19637-01/


Attachments
This solution has no attachment
  Copyright © 2012 Sun Microsystems, Inc.  All rights reserved.
 Feedback