Sun Microsystems, Inc.  Sun System Handbook - ISO 4.1 October 2012 Internal/Partner Edition
   Home | Current Systems | Former STK Products | EOL Systems | Components | General Info | Search | Feedback

Asset ID: 1-71-1021109.1
Update Date:2012-10-09
Keywords:

Solution Type  Technical Instruction Sure

Solution  1021109.1 :   Sun StorageTek[TM] 6140, 6540, and Flexline 380 Array Controller 7-Segment LED  


Related Items
  • Sun Storage 6140 Array
  •  
  • Sun Storage Flexline 380 Array
  •  
  • Sun Storage 6540 Array
  •  
Related Categories
  • PLA-Support>Sun Systems>DISK>Arrays>SN-DK: FLX300_65xx_6780
  •  
  • .Old GCS Categories>Sun Microsystems>Storage - Disk>Modular Disk - 6xxx Arrays
  •  
  • .Old GCS Categories>Sun Microsystems>Storage - Disk>Modular Disk - Flexline FLX FLA FLC Arrays
  •  

PreviouslyPublishedAs
271029


Applies to:

Sun Storage Flexline 380 Array - Version Not Applicable and later
Sun Storage 6140 Array - Version Not Applicable and later
Sun Storage 6540 Array - Version Not Applicable and later
All Platforms

Goal

The purpose of this document is to describe how the seven(7) segment display on the RAID controller module works, for a Sun StorageTek[TM] 6540, StorageTek[TM] Flexline 380, and Sun StorageTek[TM] 6140. Additionally, it will describe the codes that can be displayed.
The seven segment displays on these arrays are static. Under optimal conditions they will display the tray ID, which is 85 by default. 

On boot, the array controllers will go through a rapid sequence of displays, which indicate the points in the boot cycle that the controllers are performing.  This document is intended to describe the static display, which does not change after the boot sequence has stopped. The static display indicates the reason why the boot sequence is stopped, and will be accompanied by an Amber Fault LED next to the display that indicates that the controller is offline as well. 

Fix

Follow the steps below to reference the meaning of the tray ID.

1. Verify that you're looking at the RAID module or controller.

The RAID module is a piece of hardware that contains only the RAID controllers and power distribution components for the module,
pictured here in the Sun System Handbook.  This applies to a Flexline 380 and a 6540 array.

The RAID controller tray is a tray of drives that contains a pair of RAID controllers, instead of expansion modules.  The difference
being that the controllers have ethernet network ports on them. An example is pictured here in the Sun System Handbook. This applies to a 6140 array.

If your array is not a 6140, 6540, or Flexline 380, but has a seven segment display on the RAID controller tray or module, you are likely looking at a 6580, 6780, or 6180 array.  Please reference <Document 1021110.1> Sun Storage[TM] 6x80 and 2500-M2 Array Controller 7-Segment Display. Otherwise, continue.

2.  Review the tables below against what you are seeing on your display for it's meaning. 

Common Codes

Code Description
5d or Sd Controller is booting it's operating system
85 This is the DEFAULT TRAY ID, displayed during normal operation
Although it can be set to anything between 85 - 93 it is not recommended to do so.
88 Controller is being held offline by it's alternate controller

Lockdown Codes

These codes are display if the controller has been "locked down", which generally means the controller is non-operational.

Code Description
L0 Mismatched Controller Types
The Board IDs of the controllers (or any of their daughter card IDs) do not match.
L1 Missing Interconnect Cannister
An expected controller interconnect device (used for intercontroller communication) is not present.
L2 Persistent Memory Errors
Persistent ECC memory errors in either processor or RPA memory.
L3 Persistent Hardware Errors
Either PCI errors or memory initialisation errors have occurred.
L4 Persistent Data Protection Errors
Persistent EDC errors have occurred.
L5 Automatic Code Synchronisation (ACS) Failure
Alternate controller has incompatible firmware, and Automatic Code Synchronisation (ACS) is not permitted.
L6 Unsupported Host Card
The current level of firmware does not support the host card.
L7 Sub Model Identifier Not Set or Mismatched
The sub-model ID of the controllers do not match, or the controller's sub-model is not set or is set to an value unsupported by the firmware.
L8 Memory Configuration Error
Unsupported memory configuration - unsupported memory present, or memory is not in the correct memory slots
L9 Link speed mismatch
LF Lock-down with limited Management access
LH Controller firmware mismatch
LU Controller Reboot Limit Exceeded

Hardware Initialization Patterns

These codes are displayed momentarily while the controller hardware is initialised.
These codes are typically not visible, unless the controller firmware hangs while executing that function.

Code Description
E5 Invoke ABS
EE BIST Failure
F1 Processor Set-up
F2 TXC Chip Set-up
F3 Cache Disable
F4 Memory Test
F5 Invoke Boot Firmware
F6 Invoke Core Initialisation
F7 Clear Boot Memory
F8 Enable Protected Mode
F9 Memory Test Failure
FA 440BX Chip set-up
FB Start Mode Determination
FC Intel Processor Initialisation
FD Intel Chipset Initialisation
FE Intel Memory Initialisation

Hardware Initialization Errors

These codes are display if the controller encounters an error during hardware initialization.
If these codes persist after powercycling the controller then the controller should be replaced.

Code Description
E3 Wrong number of host channel devices on the PCI bus
(probably because one or more host chips are dead)
E4 Wrong number of drive channel devices on the PCI bus
(probably because one or more of the drive chips are dead)
E5 No RPA device on the PCI bus
(probably because the RPA chip is dead)

References


Attachments
This solution has no attachment
  Copyright © 2012 Sun Microsystems, Inc.  All rights reserved.
 Feedback