How to replace a Lithium Battery in a Sun Blade[TM] X6250 Server Module [Video]

Asset ID:	1-71-1011366.1
Update Date:	2010-10-07
Keywords:

Solution Type Technical Instruction Sure

Solution 1011366.1 : How to replace a Lithium Battery in a Sun Blade[TM] X6250 Server Module [Video]

Applies to:

Sun Blade X6250 Server Module
Sun Blade 6000 System - Version: Not Applicable and later [Release: NA and later]
All Platforms

Goal

Description
This document explains how to physically replace and install a Lithium battery in a Sun Blade[TM] X6250 Server Module. It does not explain how to diagnose a faulty battery.

Available for this topic, a Video Tutorial; Brief how-to video tutorials that provide step-by-step instructions answering Sun's most frequently asked questions. View the video answer and/or follow the detailed instructions below.

Video - X6250 Battery Replacement (5:00)

Sunsolve users must download the attachment to view the video.

Solution

Steps to Follow
How to replace a Lithium Battery in a X6250 Server Module

Note: Always refer to the X6250 Server Module Service Manual 820-1185-XX at http://docs.sun.com/ for the latest updated procedures and ESD protection standards.

Caution: When removing a server module, install a slot filler within one minute to avoid adjacent modules from overheating.

Tools

Antistatic wrist strap
Stylus

Assumptions

The server blade OS has been shut down, the module has been powered off, and the server module is lying on an anti-static mat.

Replacement Steps

1. Remove the top cover of the server module.

a ) Press down on the cover release button and, using the indent for leverage, slide the main cover toward the rear of the server module approximately 0.5 inches (12mm).

b) Grasp the cover by it's rear edge and lift it straight up from the module.

2. Remove the REM. (if equipped)

a) Disengage the REM connector from the motherboard by pulling up on the connector side of the module.

b) Once the connector is free pull the REM away from the motherboard support bracket at an upward angle.

c) Now that the REM has been removed the lithium battery should be visible as it resides underneath the REM.

3. Remove the server module battery.

Note: Note the orientation (polarity) of the battery in its holder before removing it. The positive polarity, marked with a "+" symbol, should be facing up.

a) Use a flat head tool or stylus to pry one side of the circular battery out of its socket.

b) Lift the battery up and out of its socket.

4. Install the replacement server module battery.

a) Place the battery in the open socket, with the positive polarity facing up.

b) Push the battery down until it snaps into the socket.

5. Install the replacement REM. (if equipped)

a) Turn the REM over so that its circuit side faces the motherboard and the REM connector is on the same side as its motherboard connector.

b) Angle the back end of the REM into the support bracket.

c) Press the REM connector to the motherboard connector carefully.

d) Push down on the connector until the connector is fully engaged.

6. Once the REM has been replaced reinstall the top cover.

a) Align the top cover with the guide notches and place flat on the server module.

b) Slide the top cover forward until the cover release button clicks in place with the locking mechanism.

Product
Sun Blade X6250 Server Module
Sun Blade 6000 Modular System

X6250, SB6000, battery, coin, lithium, replace, install
Previously Published As
90699

Change History
Date: 2007-09-27
User Name: 71396
Action: Approved
Comment: Publishing
Version: 5
Date: 2007-09-27
User Name: 71396
Action: Update Started
Comment: Adding tutorial
Version: 0
Date: 2007-09-22
User Name: 71396
Action: Approved
Comment: Performed final review of article.
Product_uuid
9ece394b-d285-11db-9135-080020a9ed93|Sun Blade X6250 Server Module
f2ef019c-d283-11db-9135-080020a9ed93|Sun Blade 6000 Modular System

Attachments

This solution has no attachment