E3000 / E4000 / E5000 / E6000
E3500 / E4500 / E5500 / E6500
CPU/Memory Board
Option 2600
501-2976 |
0MB FRU w/o Module 83MHz Gigaplane |
Backpanel
Jumper Settings
JUMPER |
PINS |
SETTING |
DESCRIPTION |
FAB 270-2976 |
J2502 |
1-2 |
Out |
Inv Adr 1 |
-01 -02 -03 -04 |
J2503 |
1-2 |
In |
|
-01 -02 |
Notes
- The minimum OS for the Ex000 is Solaris 2.5.1.
- The minimum OS for the Ex500 is 2.5.1 HW: 11/97 or 2.6 HW: 3/98.
- OBP >=3.2v14 is required when 83MHz and 100MHz boards are mixed.
- OBP >=3.2v23 is required when 256MB DIMMs are installed.
OBP 3.2v29 fixes mirrored SRAM identification BugID 4427581.
See Patch
103346.
- The message "status `fail - Downrev AC' " is displayed when CPU Board
<501-2976-03 is installed. The message indicates that the Address
Controller is pre-FCS and lower than revision 5.
- Refer to the Install.info file of any Firmware patch for
information on firmware verification and compatibility.
Compatibility Notes
- The 501-2976 was shipped in the E3000 - E6000.
- The 501-2976 was not shipped in the E3500 - E6500.
- The 501-2976 is supported in the E3000 - E6000 and E3500 - E6500.
Flash PROM Notes
- Use the Flash PROM Programming Utility to update the flash PROM.
- Use the prom-copy (src dst -) command to copy a flash PROM.
- ok 2 b prom-copy (copies from board 2 to board 11)
- Use the update-proms command to synchronize the latest version of
flash PROM installed in the system to all boards of the same type.
Module Notes
- The 501-2976 supports up to 2MB of cache per module. If modules
with greater than 2MB are installed, only 2MB will be addressed.
- The 250MHz 1MB module requires OBP 3.2 Version 6.
- The 250MHz 4MB module requires OBP 3.2 Version 7.
- The 336MHz 4MB module requires OBP 3.2 Version 12.
- The 400MHz 4MB module is not supported.
- The 400MHz 8MB module requires OBP 3.2 Version 21.
References
-
Ultra Enterprise 3000 System Manual, 802-6051.
-
Ultra Enterprise 4000/5000/6000 System Manual, 802-3845.
-
System Flash PROM Programming Guide, 802-5579.
E3000 / E4000 / E5000 / E6000
E3500 / E4500 / E5500 / E6500
CPU/Memory Board
Option 2601
501-4312 |
0MB FRU w/o Module 83MHz Gigaplane |
Backpanel
Jumper Settings
JUMPER |
PINS |
SETTING |
DESCRIPTION |
J2502 |
1-2 |
Out |
Inv Adr 1 |
Notes
- The minimum OS for the Ex000 is Solaris 2.5.1.
- The minimum OS for the Ex500 is 2.5.1 HW: 11/97 or 2.6 HW: 3/98.
- The first OBP release for the 501-4312 was 3.2 Version 7.
- OBP >=3.2v14 is required when 83MHz and 100MHz boards are mixed.
- OBP >=3.2v23 is required when 256MB DIMMs are installed.
OBP 3.2v29 fixes mirrored SRAM identification BugID 4427581.
See Patch
103346.
- Refer to the Install.info file of any Firmware patch for
information on firmware verification and compatibility.
Compatibility Notes
- The 501-4312 was shipped in the E3000 - E6000.
- The 501-4312 was not shipped in the E3500 - E6500.
- The 501-4312 is supported in the E3000 - E6000 and E3500 - E6500.
Flash PROM Notes
- Use the Flash PROM Programming Utility to update the flash PROM.
- Use the prom-copy (src dst -) command to copy a flash PROM.
- ok 2 b prom-copy (copies from board 2 to board 11)
- Use the update-proms command to synchronize the latest version of
flash PROM installed in the system to all boards of the same type.
Module Notes
- The 501-4312 supports up to 8MB of cache per module.
- The 250MHz 2MB module requires OBP 3.2 Version 6.
- The 250MHz 4MB module requires OBP 3.2 Version 7.
- The 336MHz 4MB module requires OBP 3.2 Version 12.
- The 400MHz 4MB module is not supported.
- The 400MHz 8MB module requires OBP 3.2 Version 21.
References
-
Ultra Enterprise 3000 System Manual, 802-6051.
-
Ultra Enterprise 4000/5000/6000 System Manual, 802-3845.
-
System Flash PROM Programming Guide, 802-5579.
E3000 / E4000 / E5000 / E6000
E3500 / E4500 / E5500 / E6500
CPU/Memory Board
Option 2602
501-4882 |
0MB FRU w/o Module
83/90/100MHz Gigaplane |
Backpanel
Jumper Settings
JUMPER |
PINS |
SETTING |
DESCRIPTION |
J2502 |
1-2 |
Out |
Inv Adr 1 |
Configured CPU/Memory FRUs
PART # |
DESCRIPTION |
MODULE # |
540-4516 |
0MB FRU with 2 400MHz Modules |
501-5762 |
540-4517 |
0MB FRU with 2 400MHz Modules |
501-5661 |
540-4575 |
2GB FRU with 2 400MHz Modules |
501-5762 |
540-4732 |
0MB FRU with 2 400MHz Modules |
501-5838 |
540-4867 |
2GB FRU with 2 400MHz Modules |
501-5838 |
540-4893 |
2GB FRU with 2 400MHz Modules |
501-6009 |
540-4894 |
0MB FRU with 2 400MHz Modules |
501-6009 |
540-4955 |
0MB FRU with 1 400MHz Module |
501-5838 |
540-4956 |
0MB FRU with 1 400MHz Module |
501-6009 |
540-5396 |
0MB FRU with 2 400MHz Modules |
501-5815 |
540-5397 |
2GB FRU with 2 400MHz Modules |
501-5815 |
540-5400 |
0MB FRU with 1 400MHz Module |
501-5815 |
Notes
- The minimum OS for the Ex000 is Solaris 2.5.1.
- The minimum OS for the Ex500 is 2.5.1 HW: 11/97 or 2.6 HW: 3/98.
- The first release of OBP for the 501-4882 was 3.2 Version 12.
- The oldest supported release of OBP for the 501-4882 is 3.2v14.
- OBP 3.2v14 is required when 83MHz and 100MHz boards are mixed.
- Refer to the Install.info file of any Firmware patch for
information on firmware verification and compatibility.
Compatibility Notes
- The 501-4882 was shipped in the E3500 - E6500.
- The 501-4882 was not shipped in the E3000 - E6000.
- The 501-4882 is supported in the E3000 - E6000 and E3500 - E6500.
Flash PROM Notes
- Use the Flash PROM Programming Utility to update the flash PROM.
- Use the prom-copy (src dst -) command to copy a flash PROM.
- ok 2 b prom-copy (copies from board 2 to board 11)
- Use the update-proms command to synchronize the latest version of
flash PROM installed in the system to all boards of the same type.
Module Notes
- The 400MHz 4MB module requires OBP 3.2 Version 18.
- The 400MHz 8MB module requires OBP 3.2 Version 21.
- The 464MHz 8MB module requires OBP 3.2 Version 29.
References
-
Enterprise 3500 System Reference Manual, 805-2630.
-
Enterprise 4500/5500/6500 System Reference Manual, 805-2632.
-
System Flash PROM Programming Guide, 802-5579.
|