20GB 4 mm DDS-1 Autoloader
Servers: |
SPARCcenter 2000 |
Options 825 / 826 / 827
370-1616 |
370-1617 |
Archive 4584NP Light Grey Bezel |
Archive 4584NP Black Bezel |
Operator Panel |
|
|
LMJB0153 PCB |
|
Address Select Switch Cable
|
In the Multi-Tape Backup Tray and SC2000, orient the Address Select
Switch Cable as shown, and plug it into JP6. |
Note
- Remove the mylar sheet from the bottom of the drive before installation.
References
-
20GB 4mm Autoloader Destop Storage Module Installation and User's Guide, 801-5401.
-
Product Note, 801-6234.
Jumper and Switch Settings
JP4
PINS |
SETTING |
DESCRIPTION |
1-2 |
Out |
Disable TERMPWR to bus |
1-2 |
In |
Enable TERMPWR to bus |
|
|
JP6
SCSI ID |
3 |
2 |
1 |
0 |
Out |
Out |
Out |
1 |
Out |
Out |
In |
2 |
Out |
In |
Out |
3 |
Out |
In |
In |
4 |
In |
Out |
Out |
5 |
In |
Out |
In |
6 |
In |
In |
Out |
|
|
SW1
SWITCH |
SETTING |
DESCRIPTION |
1 |
Off |
Enable SCSI ID 0 = 20
|
2 |
Off |
Enable SCSI ID 1 = 21 |
3 |
Off |
Enable SCSI ID 2 = 22 |
4 |
On |
Enable SCSI-2 mode |
5 |
On |
Enable parity |
6 |
Off |
Enable data compression |
7 |
Off |
Reserved for factory use |
8 |
On |
Enable power-on self test |
|
Switch Settings
LMJB0178 PCB |
|
|
S1 |
SWITCH |
SETTING |
DESCRIPTION |
1 2 |
Off* Off* |
English language display |
1 2 |
Off On |
French language display |
1 2 |
On On |
Spanish language display |
1 2 |
On Off |
German language display |
3 3 |
Off On* |
Stop after last tape
Restart at Tape 1 after last tape |
4 4 |
On* Off |
High intensity display
Low intensity display |
5 |
On* |
Enable power-on self test |
6 |
Off |
Not used |
7 |
Off |
Not used |
* Default settings
|
|
|
Auto-Loader |
|
|
S5 |
SWITCH |
SETTING |
DESCRIPTION |
1 |
Off* On |
Horizontal character display
Vertical character display |
2 |
Off On* |
Do NOT load tape on power-up
Load tape on power-up |
3 |
Off On* |
Stop after last tape
Restart at first tape after last tape |
4 |
Off |
Not used |
* Default settings
|
|
Notes
- The minimum operating system is Solaris 2.2.
- Solaris 2.2 reads and writes in low-density or high-density mode.
- The 4-Tape Magazine part number is 370-1683-01.
- The Blank 90 Meter Tape part number is 370-1612-01
- The Cleaning Kit part number is 370-1613-01.
- Firmware update tape 4.CDA-424 is part number 370-2867-01.
- Firmware update tape 4.CDB-424 is part number 370-3270-01.
References
-
20 Gbyte 4mm Tape Auto-Loader Installation Manual, 801-4976.
-
20 Gbyte 4mm Tape Auto-Loader User's Guide, 801-4977.
|